manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 84

Test Setup - Test Applications

72

88000 Series

Carrier Ethernet OAM

Carrier Ethernet OAM 

The Carrier Ethernet OAM test application supports the following tests: 

Ethernet OAM (S-OAM)

, 

MPLS-TP OAM

, and 

Link OAM

. 

Ethernet OAM and MPLS TP OAM 

The Ethernet Service OAM tests are divided into two main categories: 

Performance Monitoring measures parameters such as frame delay, 
frame loss, and synthetic loss (Y.1731/MEF). 

Connectivity Fault Management provides the capability for detecting, 
verifying, and isolating connectivity failure (Y.1731/802.1ag/MEF). 

Typical Ethernet OAM and MPLS TP OAM test applications: 

Supported Interfaces/Rates: 10M to 10G LAN/WAN. 

MIP 

EXFO Module

Peer MEP

Local MEP

MIP 

EXFO Module

Local MEP

EXFO Module

Smart Loopback with 

S-OAM Responder enabled.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands