manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 125

Test Setup - Test Configurator, Timer, and System

Power Blazer

113

Modify Structure Button

OTN Multiplexing

 - 

Config Mux

 button allows the selection of the OTN 

test mapping including the selection of the payload type (PT20 or 
PT21) when applicable. Refer to 

OTN BERT

 on page 45 and 

OTN-SONET/SDH BERT

 on page 47 for supported path/mapping. 

Note:

For Multi-Channel OTN, ODU0 mapping is selected by default and the 

OTN Multiplexing

 field is not displayed. Refer to Modify Trib 

Slots/Channels

 on page 240

 for test mapping selection and Multi-Channel 

OTN

 on page 44

 for supported path/mapping. 

Interface/Rate

OTN Multiplexing

OTU1 [2.666 Gbit/s] ODU1 

ODU1/ODU0 

OTU2 [10.709 Gbit/s] ODU2 

ODU2/ODU1 
ODU2/ODU1/ODU0
ODU2/ODU0 
ODU2/ODUflex 

OTU1e [11.049 Gbit/s] ODU1e
OTU2e [11.096 Gbit/s] ODU2e
OTU1f [11.270 Gbit/s] ODU1f
OTU2f [11.318 Gbit/s] ODU2f
OTU3 (4 Lanes) [43.018 Gbit/s]

ODU3

 

ODU3/ODU2
ODU3/ODU2/ODU1
ODU3/ODU2/ODU1/ODU0
ODU3/ODU1
ODU3/ODU1/ODU0
ODU3/ODU0
ODU3/ODUflex 

OTU3e1 (4 Lanes) [44.571 Gbit/s]

ODU3e1

OTU3e2 (4 Lanes) [44.583 Gbit/s]

ODU3e2

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands