manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 321

Test Setup - Test Configurator, Timer, and System

Power Blazer

309

Signal - Signal Configuration (SONET/SDH)

STS/AU Path (SONET/SDH HOP): 

The following diagram shows a test case data path that is terminated 
right after SONET/SDH high order path. High order background traffic is 
automatically adapted to the rate (STS-1, AU-3, or AU-4) signal level for 
the paths that are not defined in the test case. In the situation where 
the traffic pattern is replaced by GFP the background traffic remains 
the same for the STS-1/AU-3/AU-4 that are not involved in the test case 
data path. In the situation where contiguous concatenation or virtual 
concatenation is used, the background traffic continues to be applied 
on the remaining timeslots not involved in the test case data path.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands