manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 183

Test Setup - Test Configurator, Timer, and System

Power Blazer

171

External Reference

External Reference 

Allows the configuration of the external reference signal. Available with 
Wander test application. 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and tap on the 

External Reference

 block. 

Reference 

Mode

 is set to 

External Reference

. 

Ext Reference In 

Allow the selection of the reference signal for TE/TIE measurements. 

Signal

 allows the selection of the reference interface: 

2 MHz

, 

10 MHz

, 

and

 1PPS

. Only 

1PPS

 reference is available for 1PPS interface/rate test. 

Ext Ref In

 on a green background indicates that a valid reference is 

received. 

LOS

 on a red background indicates that the received signal is not valid. 

Connector

 indicates the connector used for the external reference 

signal: 

RJ48C

 or 

BNC. 

Frequency (MHz)

 displays the frequency of the received reference 

signal. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands