manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 771

Power Blazer

759

C Remote ToolBox 

Overview

The 

Remote ToolBox

 application allows remotely controlling a module 

installed on a platform using a remote PC. Remote users are connected to 
the platform using an Ethernet connection. 

Note:

The remote control feature has to be enabled for the module on its specific 
slot on the 

platform

. Refer to the 

Controlling Modules Remotely

 section 

from the platform user guide for more information. 

The 

Remote ToolBox

 allows starting one or several module application(s). 

Once a module application is started, the application is independent and 
does not require the 

Remote ToolBox

 anymore. Thus, the 

Remote 

ToolBox

 application can be closed or can be disconnected from the 

platform using the 

Disconnect

 button without affecting the running remote 

module applications. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands