manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 177

Test Setup - Test Configurator, Timer, and System

Power Blazer

165

EtherSAM - Global

EtherSAM - Global 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, tap on the test block, 

and on the 

Global

 tab. 

Dual Test Set 

Dual Test Set 

(

DTS

) check box when selected (cleared by default) 

enables EtherSAM 

Dual Test Set

. Once 

Dual Test Set

 is enabled, use 

the 

Discover Remote

 button to select a remote unit. Not available in 

Dual Port

 topology. 

Note:

It is also possible using the Discover Remote button to connect to a remote 
module and automatically enable Dual Test Set. For more details, refer to 

Discover Remote Button

 on page 636. 

Disconnected

 indicates that there is no connection established 

with a remote module. 

NAT LAN/WAN

 and 

WAN IP

 indicate presence of NAT (Network 

Address Translation) router. The NAT router is automatically 
detected and graphically displayed with LAN/WAN indication as 
well as the WAN IP address when the module is behind a NAT 
router. 

Note:

When there is a NAT at the Remote site, it is required to create UDP/TCP 
port 62819 forwarding rule on this NAT router to allow DTS communication. 
In addition, when there is a NAT in both directions (L->R and R->L), it is 
also required to create port forwarding rules on the NAT router located at 
the Remote side for every service defined. 

Discover Remote

 button allows discovering remote modules 

supporting 

Remote Loopback

 and/or 

Dual Test Set

. For more details, 

see 

Discover Remote Button

 on page 636. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands