manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 279

Test Setup - Test Configurator, Timer, and System

Power Blazer

267

S-OAM and MPLS-TP OAM

S-OAM and MPLS-TP OAM 

From the test menu, tap

 Setup

, 

Test Configurator

, and the 

S-OAM (Y.1731/802.1ag/MEF

) or 

MPLS-TP OAM (G.8113.1)

 test block. 

OAM Mode 

Allows the selection of the OAM mode. 

OAM Type

OAM Mode

S-OAM Y.1731

 (default) supports both Connectivity Fault Management and 

Performance Monitoring which includes all S-OAM functions supported by 
this module. 

802.1ag

 supports Connectivity Fault Management including only the 

Continuity Check, Loopback, Link Trace, and RDI functions. 

MEF

 supports both Connectivity Fault Management and Performance 

Monitoring which includes all S-OAM functions supported by this module. 

MPLS-TP OAM

  G.8113.1 (default) supports both Connectivity Fault Management and 

Performance Monitoring which includes all MPLS-TP OAM functions 
supported by this module. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands