manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 581

Test Functions

Power Blazer

569

Filters

Filter

 specifies the filter to be used (

None

 by default). 

Value

 is the value associated to the selected filter. 

Category 

Filter 

Ethernet

MAC Destination Address

, 

MAC Source Address

, 

EtherType

a

, 

C-VLAN ID

, 

S-VLAN ID

, 

E-VLAN ID

, 

C-VLAN Priority

, 

S-VLAN Priority

, 

E-VLAN Priority

a.

Applies only to the last EtherType occurrence when VLAN is used.

IPv4

IPv4 Destination Address

, 

IPv4 Source Address

, 

IPv4 TOS

, 

IPv4 Precedence

, 

IPv4 Protocol

, 

IPv4 DiffServ

IPv6

b

b.

Available when the corresponding software option is enabled (refer to

page 34).

IPv6 Destination Address

, 

IPv6 Source Address

, 

IPv6 Flow Label

, 

IPv6 Next Header

c

, 

IPv6 Traffic Class

, 

IPv6 

Precedence

, 

IPv6 DiffServ

 

c.

Applies only to the last next header occurrence when extension headers are

used.

Higher Layer

 

TCP Destination Port

d

, 

TCP Source Port

d

, 

UDP Destination Port

, 

UDP Source Port

 

d.

Available with 10M to 10G interface rates only. 

MPLS

b

M

PLS Label 1

, 

MPLS Label 2

, 

MPLS COS 1

, 

MPLS COS 2

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands