manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 133

Test Setup - Test Configurator, Timer, and System

Power Blazer

121

Modify Structure Button

PHY Type

 allows selecting the 100GE (4 Lanes) CFP4/QSFP transceiver 

PHY type: 

LR4/ER4

(default), 

SR4

, 

CWDM4

, 

CLR4

, or 

Other

. The PHY 

type when set to any except 

LR4/ER4

, allows enabling RS-FEC (see 

page 182); ensure both ends of the circuit have the FEC enabled. Only 
available with 100GE (4 Lanes) framed Ethernet interface. 

Primary Port / Secondary Port

, available with Through Mode test 

application, allows selecting the module’s ports that are respectively 
used as primary (Port 1) and secondary (Port 2) port. The configuration 
of the network configuration parameters will be available on the 
Primary Port only. 

Connector

 allows the selection of the module’s port. 

Interface/Rate

Connector

a

a.

Availability of connectors depend on the model. 

8870/8880 

88200NGE 

88260 

88400NGE 

400GE (8 Lanes) [425 Gbit/s]

-

-

-

Port 1 - CFP8 

100GE (4 Lanes) [103.125 Gbit/s] 

-

Port 1 - CFP4
Port 2 - QSFP

b

 

b.

This port accepts QSFP+ or QSFP28 transceivers. 

-

-

40GE (4 Lanes) [41.25 Gbit/s]

-

Port 2 - QSFP

b

 

-

-

25GE

 

-

-

Port A1 - SFP28
Port A2 - SFP28
Port B1 - SPF28
Port B2 - SFP28

-

10GE WAN 
10GE LAN 
1GE Optical 
100M Optical 

Port 1 - SFP+
Port 2 - SFP+

Port 1 - SFP+ 

-

-

10/100/1000M Electrical 

Port 1 - RJ45 
Port 2 - SFP+ 
(RJ45)

c, d

c.

Only available as a second port when the test application requires two ports. 

d.

Ethernet 10/100/1000M electrical is supported when using an active copper SFP. 

Port 1 - SFP+ 
(RJ45)

d

 

-

-

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands