manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 238

Test Setup - Test Configurator, Timer, and System

226

88000 Series

Network Details (iSAM)

Network Details (iSAM) 

Either select the Layer parameter, the number of services, for each service 
the profile and CIR settings, or click on 

More

 for all settings. 

The total bandwidth (when the 

Performance Test

 is enabled) and the 

estimated test duration are also displayed. 

NAT LAN/WAN

 indicate presence of NAT (Network Address Translation) 

router. The NAT router is automatically detected and graphically displayed 
with LAN/WAN indication.

Note:

When there is a NAT at the Remote site, it is required to create UDP/TCP 
port 62819 forwarding rule on this NAT router to allow DTS communication. 
In addition, when there is a NAT in both directions (L->R and R->L), it is 
required to create port forwarding rules on the NAT router located at the 
Remote side for UDP port 7. 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and the 

More

 button 

from the 

Network

 block. 

iSAM 

Layer

 is the layer used for all services. The layer is fixed to 

L3/L4

 when 

the 

RFC 6349 Test

 is enabled. 

L2

(default) for Ethernet II. 

L3/L4

 for Ethernet II, IP (IPv4), and respectively UDP for the 

Configuration and Performance subtests, and TCP for RFC-6349 
subtest. 

Classification

 defines the traffic classification used in the provider 

network: 

VLAN ID

, 

VLAN Priority

, or 

DSCP

 (available with layer L3/L4). 

Note:

At least one check box (

Configuration Test

, or 

Performance Test

, or 

RFC 6349 Test

) has to be selected. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands