manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 134

Test Setup - Test Configurator, Timer, and System

122

88000 Series

Modify Structure Button

Framing

, available for EtherBERT test application, allows the selection 

of the test framing type; otherwise the framing is set to Framed Layer 2. 
See 

Network

 on page 220 for more information on frame format. 

The framing is not configurable and set to 

Framed Layer 2

 for 

40GE/100GE dual port topology and for 400GE test.

Framed Layer 1

: Frame of x bytes that allows connection to any 

interface that complies with 802.3 Ethernet PHY or DWDM fibre. 
Available with rate up to 10G WAN. 

Framed Layer 2

: Frames of x

1

 bytes without network layer (

None

) 

that complies with IEEE 802a Ethernet II standard. 

Framed Layer 3/4 

(default): Frames of x

1

 bytes with UDP (default) 

or TCP network layer that complies with IEEE 802a Ethernet II 
standard. 

1. To set the frame length, see Frame Size on page 161 for EtherBERT (Ethernet and EoOTN) and page 254 for 

RFC 2544. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands