EXFO Power Blazer 88000 Series User Manual Download Page 390

Page: 390 / 803

Test Results

378

88000 Series

Alarms/Errors Overview

ODUx

Note:

For OPUx alarms see page 383. For GMP alarms/errors see page 373.

Alarms



AIS

(Alarm Indication Signal)

: The STAT information in the PM byte 3, bits 6 to 8 is “111” for at

least 3 consecutive frames.

: Generates an all "1"s pattern in the entire ODUk signal, excluding

the frame alignment overhead (FA OH), OTUk overhead (OTUk OH)
and ODUk FTFL.



BDI

(Backward Defect indication)

: The BDI bit in the PM overhead field (byte 3, bit 5) is “1” for at least

5 consecutive frames.

: Generates a “1” in the BDI (byte 3, bit 5) of the PM overhead field

continuously.



BSD

(Backward Signal Degrade)

: The FTFL byte 128 is “00000010”.

: Generates a “00000010” pattern in the FTFL Byte 128 continuously.



BSF

(Backward Signal Fail)

: The FTFL byte 128 is “00000001”.

: Generates a “00000001” pattern in the FTFL Byte 128 continuously.



FSD

(Forward Signal Degrade)

: The FTFL byte 0 is “00000010”

: Generates a “00000010” pattern in the FTFL Byte 0 continuously.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands