manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 229

Test Setup - Test Configurator, Timer, and System

Power Blazer

217

MAC/IP/UDP

TTL

 (IPv4) or 

HOP Limit TTL

 (IPv6) sets the Time To Live value: 

1

 to 

255

 (default is 

128

). 

Flow Label

 (IPv6) is a number used to identify a series of related 

packets from a source to a destination: 

0

 (default) to 

1048575

. 

IP TOS/DS

 (IPv4) or 

Traffic Class (TOS/DS) 

- (IPv6) allows entering 

either an hexadecimal value, 

00

 (default) to 

FF

, or tap on the 

TOS/DS 

Config

 button to set each TOS or DS parameter individually. Changing 

the 

IP TOS/DS

 value will affect the 

TOS/DS Config

 settings and vice 

versa. 

TOS/DS Config

 button allows setting the Type of Service or the 

Differentiated Service parameters. 

TOS/DS

 

TOS/DS

 allows selecting either Type Of Service (TOS) or 

Differentiated Services (DS). 

Binary/Hex

 allows displaying, once this pop-up is closed, the IP 

TOS/DOS value either in binary or hexadecimal. 

Type Of Service

 (available when 

TOS

 is selected). 

Precedence

 value: 

000 (Routine)

 (Default)

001 (Priority)
010 (Immediate)
011 (Flash)
100 (Flash Override)
101 (CRITIC/ECP)
110 (Internet Control)
111 (Network Control)

Delay 

allows the selection of the delay level: 

Normal

 (default) or 

Low

. 

Throughput

 allows the selection of the throughput level: 

Normal

(default) or 

High

. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands