manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 653

Test Control

Power Blazer

641

Lpbk Tool Button (Loopback Tool)

Loopback Tool tab 

The 

Loopback Tool

 tab allows the configuration of the loopback 

parameters and displays the traffic statistics as well as the S-OAM 
Responder statistics. 

Press the 

Lpbk Tool 

button and select the 

Loopback Tool 

tab.

Status

: The status field displays the current status of the Loopback test.

-- (Idle): 

Loopback Tool is not looping back frames and results are 

not available. 

In Progress

: Loopback Tool is looping back frames. 

Completed

: Loopback Tool is not looping back frames but results 

are available. The test 

Status

 indicates 

Completed

 when the 

loopback tool has been stopped. 

Start Time: 

The time when the Loopback Tool was started. 

Transparent (Pseudo-Physical

) check box when selected (cleared by 

default), determines that the Loopback tool operates as a physical 
loopback by transmitting all received frames unaltered and without 
discrimination. 

In transparent mode, the Network tab and the S-OAM Responder 
statistics are not available.

 

Note:

The 

Transparent

 mode is intended to be used for point-to-point topology, 

not for switched or routed networks. Use the 

Transparent

 mode with 

caution because all received frames are looped back without 
discrimination. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands