manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 328

Test Setup - Test Configurator, Timer, and System

316

88000 Series

Streams - Profile

Profile

Profile

 button allows the selection and configuration of either 

Voice

, 

Video

, or 

Data

 (default) emulation profile. The selected profile icon 

and its Codec for Voice and Video are displayed next to the 

Profile

 

button. Only 

Data

 is available when using 

Provider Encapsulation

. 

Voice

 when selected allows the configuration of the following 

parameters. 

Voice Codec

 allows the selection of the codec used by the voice 

profile: 

VoIP G.711

 (default), 

VoIP G.723.1

, or 

VoIP G.729

. 

Number of Calls

 allows the selection of the number of calls that 

will be generated for the selected stream. The minimum and 
default value is 

1

 for 10M to 1G interface, 

5

 for 10G, and 

10

 for 40G 

and 100G interfaces. 

Rate

 indicates the rate corresponding to the selected codec and 

the number of calls. 

Video

 when selected allows the configuration of the following 

parameters. 

Video Codec

 allows the selection of the codec used by the video 

profile: 

SDTV (MPEG-2)

 - (default), 

HDTV (MPEG-2)

, or 

HDTV (MPEG-4)

. 

Number of Channels

 allows the selection of the number of 

channels (

1

 by default) that will be generated for the selected 

stream. 

Rate

 indicates the rate corresponding to the selected coded and 

the number of channels. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands