manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 462

Test Results

450

88000 Series

Quality Level (SyncE)

Quality Level (SyncE) 

The quality level characterizes the clock quality in terms of network 
synchronization.

From the 

Test

 menu, tap

 Results

, and the 

Quality Level 

tab. 

Generated QL

 indicates the Quality Level value that is generated. 

Last Change

 indicates the date and time of the Generated Quality 

Level value has changed. For 1GE Electrical interface using 

Local 

Clock

 set to 

Slave

, the 

Last Change

 is not available. 

Last QL Received

 indicates the last Quality Level value received. The 

pass/fail verdict is also displayed when both 

QL Mismatch Monitoring

 

and 

Pass/Fail Verdict

 check boxes are selected. 

Last Change

 indicates the date and time of the Last QL Received has 

changed. 

QL Mismatch Monitoring

 when selected (default), enables the Quality 

Level mismatch monitoring. 

Expected QL

 allows the selection of the Expected Quality Level value. 

Available when the 

QL Mismatch Monitoring

 check box is selected. 

Quality Level 

value

SSM

Description

QL-STU/UNK

0

Synchronized - Traceability Unknown

QL-PRS

1

Primary Reference Source Traceable (G.811)

QL-PRC

2

Primary Reference Clock Traceable (G.811)

QL-INV3

3

Quality Level Invalid 3

QL-SSU-A/TNC

4

Type I or V slave clock (G.812)
Traceable to Transit Node Clock (G.812 Type V)

QL-INV5

5

Quality Level Invalid 5

QL-INV6

6

Quality Level Invalid 6

QL-ST2

7

Traceable to Stratum 2 (G.812 Type II)

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands