manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 235

Test Setup - Test Configurator, Timer, and System

Power Blazer

223

Network

Global IPv6 Address

 (GUA) is used to communicate with on-link 

neighbors and for global communication with hosts outside the 
subnet. 

Mode

 

None

 disables the 

Global IPv6 Address

 and the 

Default Gateway 

Address

.

Stateless Auto

 (default) allows automatic generation of the IPv6 

address based on the Link-Local address interface ID and the 
prefix obtained from the router advertisements. If no Interface ID 
has been obtained for the 

Link Local Address,

 the global address 

will not be generated. 

Static

 allows entering the IP address.

Address

, available with 

Static

 mode, allows selecting the 

Global 

IPv6 Address

. The accepted range is from 

0000:0000:0000:0000::[Interface ID]

 to 

FFFF:FFFF:FFFF:FFFF::[Interface ID]

. The default address is

 

2001:0000:0000:0000::[Interface ID]

, where [

Interface ID

] is 

generated from the source MAC address. When the 

Address

 field 

is selected for editing using virtual keyboard, the 

Previous IPs

 

button appears allowing the selection of a previously configured IP 
address. 

Interface ID Coupled

, available when the 

Source Global IPv6 

Address

 mode is 

Static

, allows coupling the interface ID of the 

Global address to the Link-Local source address. 

Enabled

 (default): Only the 64 bit (MSB) prefix ID in the IPv6 

address is configurable, and the 64 bit (LSB) Interface ID is not 
configurable (read-only). 

Disabled

: The 64 bit (MSB) Prefix ID and 64 bit (LSB) Interface ID 

in the IPv6 address are configurable.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands