manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 413

Test Results

Power Blazer

401

Alarms/Errors Overview

ERDI-PSD

 (Enhanced RDI - Path Server Defect) - SONET 

ERDI-SD

 (Enhanced RDI - Server Defect) - SDH 

RX

: Bits 5, 6 and 7 of the G1 byte contain the “101” pattern in five 

consecutive frames.

TX

: Generates a “101” pattern for bits 5, 6 and 7 of the G1 byte.

Errors 

B3

 (BIP-8, Bit-Interleave Parity - 8 bits) 

RX

: Indicates a high order path parity error by performing an 

even-parity check over all bits of the previous SPE (SONET) / VC-N 
(SDH). 

REI-P

 (Remote Error Indicator - Path) - SONET 

HP-REI

 (HP - Remote Error Indicator) - SDH 

RX

: Bits 1 through 4 of the G1 byte contain one pattern from the 

following binary range: “0001” through “1000” (1 to 8) (located in every 
STS-1/STM-1 of an STS-n/STM-n signal. 

SyncE 

Note:

For Wander test application only 

ESMC Loss

 alarm is supported. 

Alarms

ESMC Loss

 

RX

: No ESMC valid information frames were received for more than 5 

seconds. 

QL Mismatch

 (available when the 

QL Mismatch Monitoring

 check 

box is selected) 

RX

: The received QL value does not match the Expected QL (refer to 

page 323 or page 450). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands