manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 35

Physical Interfaces and LEDs

Power Blazer

23

Port Availability on the 88000 Series

8870/8880 

The following table shows the list of available ports as well as a description 
and the signals supported for each module. 

Connector Labelled

Description and supported signal(s)

Module

8870 8880

Bantam

BANTAM

 

TX/RX2

 

RX

 

TX

 and 

RX

: DS1/1.5M, E1/2M

RX2

: DS1/1.5M

-

X

Clock IN/OUT: DS1/1.5M, E1/2M, 2 MHz

BNC

BNC

 

TX/RX2

 

TX

: E1/2M, E3/34M, DS3/45M, STS-1e/STM-0e/52M, E4/140M, 

STS-3e/STM-1e/155M

RX2

: DS3, 2 MHz, 10 MHz

-

X

Clock OUT: DS1/1.5M, E1/2M, 2 MHz

BNC
RX

 

E1/2M, E3/34M, DS3/45M, STS-1e/STM-0e/52M, E4/140M, 
STS-3e/STM-1e/155Mk, 1PPS

-

X

Clock IN: DS1/1.5M, E1/2M, 2 MHz, 10 MHz, 1 PPS

BNC
EXT CLK

 

Clock IN: DS1/1.5M, E1/2M, 2 MHz, 1 PPS

X

-

RJ45

RJ45

 

P1

Ethernet 10/100/1000 Mbit/s electrical

X

X

RJ48C

RJ48C

 DS1/1.5M, 

E1/2M

X

X

1PPS, 2 MHz, 10 MHz

-

X

Clock IN: DS1/1.5M, E1/2M, 2 MHz

-

X

Clock OUT: DS1/1.5M, E1/2M, 2 MHz

-

X

SFP/SFP+

SFP+ P1

 

or

SFP+ P2

 

Ethernet 100 Mbit/s, 1000 Mbit/s,10 Gbit/s LAN/WAN optical
CPRI 1.2, 2.4, 3.1, 4.9, 6.1, 9.8 Gbit/s
OBSAI 1.5, 3.1, 6.1 Gbit/s 
Fibre Channel 1X, 2X, 4X, 8X, 10X

X

X

SFP+ P1

OC-1/STM-0, OC-3/STM-1, OC-12/STM-4, OC-48/STM-16, 
OC-192/STM-64

a

OTU1, OTU2, OTU1e, OTU2e, OTU1f, OTU2f

a.

Port 

SFP+ P2

 is used with OC-192/STM-64 in 

Decoupled (TX

≠

RX)

 mode.

X

X

SFP+ P2

 

Ethernet 10/100/1000 Mbit/s electrical (using active copper 
SFP)

b

b.

Available as a second port when the test application requires two ports. 

X

X

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands