manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 173

Test Setup - Test Configurator, Timer, and System

Power Blazer

161

EtherBERT, FC BERT, BERT (CPRI/OBSAI), and Unframed BERT

Ethernet Frame 

Frame Size (Bytes)

 allows entering the frame size for Ethernet test 

applications. The range is from 

64

1

 to 

16000

2

. 

The following table lists each component that may affect the minimum 
frame size values.

Note:

Sending traffic with frame size >1518 in switched network may result in 
losing all frames. 

1. The minimum frame size will be adjusted according to the frame structure and components selected.
2. The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical interface.

Component

Description

VLAN

4 bytes per VLAN (up to 3 VLAN for EtherBERT test 
application and only 1 VLAN for EoOTN client)

EoE Header 

16 bytes 

EoE VLAN 

4 bytes 

PBB-TE Header

18 bytes 

B-VLAN 4 

bytes 

UDP

8 bytes 

TCP 20 

bytes 

Ethernet Header

14 bytes 

LLC and SNAP Headers 

8 bytes 

IPv4

20 bytes 

IPv6 40 

bytes 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands