EXFO Power Blazer 88000 Series User Manual Download Page 306

Page: 306 / 803

Test Setup - Test Configurator, Timer, and System

294

88000 Series

Signal - Signal Configuration (DSn/PDH)

Signal - Signal Configuration (DSn/PDH)

For SONET/SDH - DSn/PDH BERT, from the test menu, tap

Setup

Test Configurator

, and the protocol block. Only

Framing

setting and the

Loopback

button are available.

For DSn/PDH BERT and NI/CSU Emulation, from the test menu, tap

Setup

Test Configurator

, and the interface block.

Framing

Framing

allows the selection of the framing used for transmission:

DS1

DS3

E3/E4

Unframed
SF
ESF

SLC-96

Default value

Unframed
C-Bit Parity

M13

Unframed
PCM30

PCM30 CRC-4
PCM31
PCM31 CRC-4

Unframed
Framed

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands