manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 193

Test Setup - Test Configurator, Timer, and System

Power Blazer

181

GFP-F/GFP-T

GFP-F/GFP-T 

Note:

Only available with Ethernet 

1GbE

, 

10GbE

, or 

Ethernet (flex/GFP-F)

 client.

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and tap on the 

GFP-F/GFP-T 

block. 

Note:

Refer to 

Generic Framing Procedure (GFP) 

 on page 727 for more 

information on Client Data and Client Management frames.

CDF pFCS

 (Client Data Frames payload Frame Check Sequence) 

enables the presence of the payload FCS for the client frames. This 
setting is only available with 

Ethernet (flex/GFP-F)

 client.

CMF pFCS

 (Client Management Frames payload FCS) enables the 

presence of the payload FCS for the management frames. The 

CMF pFCS

 check box is automatically cleared when injecting FDI or 

RDI alarms. 

EXI

 (Extension Header Identifier) allows the selection of the type of 

GFP Extension Header. Choices are 

Null

 (0000) - (Default) and 

Linear

(0001). EXI is only configurable with 

Ethernet (flex/GFP-F)

 

client.

CID

 (Channel IDentifier) selects the communication channel used for 

the signal transmission f

or both 

Client Data

 and 

Client Management

 

frames

. Choices are from 

0

 (default) through 

255

. CID is only available 

when EXI is set to 

Linear

. 

The status 

Mismatch

 is displayed next to the CID value when the TX 

and RX CID values differ. 

Delta

 indicates the GFP state machine synchronization parameter. 

Delta is set to 1. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands