manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 157

Test Setup - Test Configurator, Timer, and System

Power Blazer

145

Cable Test

Cable Test 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, and the test block. 

Global Options 

Wiring Standard

 is the pin-to-pair assignment corresponding to the 

UTP cable used: 

T568A

 (default) or 

T568B

. 

Length Unit

 is the unit used for cable length and distance to fault 

results: 

Meter

 (default) or 

Feet

. 

PoE

 check box when selected (cleared by default) allows verifying that 

the Power Sourcing Equipment (PSE) is capable to deliver appropriate 
power (PoE) to the Powered Device (PD). The PoE test is performed 
after the cable test is executed confirming that the cable is ready to 
carry data and power: either the Wire Map test reported 

No fault

, 

Straight pair

, 

Crossed Pair

, or 

Noise (link up)

. Only available on 

8870/8880.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands