manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 448

Test Results

436

88000 Series

MPLS

MPLS 

For 

Traffic Gen and Mon

, from the test menu, tap 

Results

, 

Streams

, and 

the 

MPLS

 tab. 

For 

Though Mode

, from the test menu, tap 

Results

, 

Traffic

, and the 

MPLS

 

tab. 

Note:

For 

Dual Port

 topology, the P1 and P2 buttons allow respectively displaying 

results for port #1 (

P1

) or port #2 (

P2

). 

Label 1 and Label 2 

The number of MPLS frames transmitted (TX) and received (RX) are 
displayed for both 

Label 1

 and 

Label

 2 for each 

Stream

. Not available for 

Through Mode

 test application. 

Total TX/RX MPLS 

Line Utilization

 indicates the percentage of MPLS line rate utilization 

in TX and RX. 

Ethernet BW (%) 

(Ethernet Bandwidth) indicates the MPLS data rate 

in TX and RX. 

Frame Rate (frames/s) 

indicates the number of transmitted (TX) and 

received (RX) MPLS frames). 

Frame Count

 indicates the count of transmitted (TX) and received 

(RX) MPLS EtherType (0x8847 or 0x8848) frames regardless if FCS is 
good or not. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands