manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 172

Test Setup - Test Configurator, Timer, and System

160

88000 Series

EtherBERT, FC BERT, BERT (CPRI/OBSAI), and Unframed BERT

Shaping

TX Rate 

allows the selection of the transmission rate in percentage of 

utilization (100 percent by default), Mbit/s, Gbit/s, Frame/s, or IFG for 
Ethernet; Mbit/s, Gbit/s, MB/s, or % for Fibre Channel. For Ethernet, the 
maximum percentage is 105 percent

 

depending on the frame size 

selected. 

Enable TX

 check box is automatically selected when starting the test 

allowing stream/client generation. The 

Enable TX

 check box may also 

be selected or cleared while the test is running. Not available for FC 
BERT.

 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands