manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 642

Test Functions

630

88000 Series

Spare Bits

Spare Bits 

Note:

Spare Bits

 are not available when the framing is set to 

Unframed

. 

From the

 Test

 menu, tap 

Functions

, tap the 

Spare Bits 

tab. 

TX

Tap a spare bits field to set its value. 

Note:

All spare bits are reserved for national use and should be set to 1 when not 
used.

E4

G.751 Bit 14, 15, 16

: Choices are 

000

 to 

111

 (default). 

E3

G.751 Bit 12

: Choices are 

0

 and 

1

 (default). 

E1

S

i0

 is located in the bit 1 of the frame containing the frame 

alignment signal (FAS). Choices are 

0

 and 

1

 (default). 

S

i1

 is located in the bit 1 of the frame not containing the frame 

alignment signal (FAS). Choices are 

0

 and 

1

 (default). 

S

a4

 to 

S

a8

 are located in bit 4 to 8 of frame number 1, 3, 5, and 7 of 

sub-multiframe 1 and 2. Choices are 

0

 and 

1

 (default) or 

0000

 to 

1111

 (default) depending on the selected framing. 

TS16 Frame 0 Bit 5, 7, 8 

are located in bit 5, 7, and 8 from Timeslot 

16 of frame 0 of a E1 signal. Choices are 

000

 to 

111

 (default). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands