manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 54

Test Setup - Test Applications

42

88000 Series

iOptics

iOptics 

iOptics test application provides a quick assessment of the proper 
operation of an optical transceiver before using it in a network or test 
environment. The validation is done by running sub-tests in addition to 
monitoring transceiver power consumption and temperature. Result and 
verdict are reported for each sub-test and monitoring task. Transceiver’s 
manufacturing information is also automatically collected. 

A fiber loopback patch cord is required to perform the test with applicable 
attenuation included to protect the optical device. Bidirectional (single 
fiber) transceivers are not supported since the iOptics test requires a 
loopback. 

Typical iOptics test application: 

Supported Interfaces/Rates: 40G/100G/OTU3/OTU3e1/OTU3e2/OTU4 
parallel interfaces and all serial interfaces up to 10G/OTU2f (refer to 

Rate

 on page 245 for more information).

EXFO Module

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands