manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 80

Test Setup - Test Applications

68

88000 Series

Smart Loopback

Smart Loopback 

Allows transmitting back the received Ethernet stream of data while 
interchanging the source and destination MAC addresses, IP addresses, 
and/or UDP/TCP ports. However in 

Transparent (Pseudo-Physical

) mode 

the Smart Loopback operates as a physical loopback by transmitting all 
received frames unaltered and without discrimination. 

The Smart Loopback test can be created locally (refer to 

Ethernet Test 

Applications

 on page 87) or remotely using an EXFO unit (refer to 

Discover 

Remote Button

 on page 636) or a Third-Party device (see 

Third-Party 

Remote Loopback

 on page 69). 

Typical Smart Loopback test application: 

Supported Interfaces/Rates: 10M to 100G. 

Network

under test

Testing Unit

Smart Loopback Unit

EXFO Module

EXFO Module

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands