EXFO Power Blazer 88000 Series User Manual Download Page 232

Page: 232 / 803

Test Setup - Test Configurator, Timer, and System

220

88000 Series

Network

Network

From the test menu tap

Setup

Test Configurator

, the interface block, and

the

Network

tab.

Note:

For Through Mode test application, the Network tab is only available for the
Primary Port but the configured parameters apply to both ports.

MAC



MAC Address

indicates and allows changing, when the

Factory

Default

check box is cleared, the default and unique Media Access

Control (MAC) address given to the Ethernet port.



Factory Default

check box, when selected (default), indicates that the

factory source MAC address is used.



Frame Format

(layer 2) allows selecting

Ethernet II

(default) or

802.3

SNAP

as the frame format.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands