manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 214

Test Setup - Test Configurator, Timer, and System

202

88000 Series

Local Details (iSAM)

Speed

, available with 

10/100/1000M Electrical

 interface, allows the 

selection of the interface rate: 

10M

, 

100M

, 

1GE

, or 

Auto

; 

Auto

 is only 

available when the Auto-Negotiation check box is selected. The 
negotiated speed will be displayed next to the Speed field selection. 

Note:

Full Duplex

 is used and there is no 

Flow Control

 (pause frames received 

are ignored). 

Lasers OFF at Start-Up

 allows automatically turning off all lasers 

when starting the module or when switching from one test application 
of the same group (Ethernet or Transport) to another. This check box is 
cleared by default. 

MAC 

Address

 indicates the default and unique Media Access Control (MAC) 

address given to the Ethernet port. 

VLAN ID/Priority

 check box when selected, cleared by default, 

enables C-VLAN with VLAN Ethernet type of 8100 and allows setting 
both VLAN ID and priority. 

VLAN ID

 choices are 

0

 through 

4095

; default is 

2

; refer to 

VLAN ID and 

Priority

 on page 758 for more information. 

Priority

 choices are 

0

 (default) to 

7

. Refer to 

VLAN ID and Priority

 on 

page 758 for more information. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands