manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 227

Test Setup - Test Configurator, Timer, and System

Power Blazer

215

MAC/IP/UDP

Prefix Mask

, available with 

Static

 mode, allows specifying a prefix 

that defines the subnet. The accepted range is 

0000:0000:0000:0000:0000:0000:0000:0000

 to 

FFFF:FFFF:FFFF:FFFF:0000:0000:0000:0000

. For example: 

Global Address: 2001:0DB8:0001:0002:02AA:00FF:FE11:1111
Prefix Mask: FFFF:FFFF:FFFF:0000:0000:0000:0000:0000 
Corresponding Prefix: 2001:0DB8:0001.

Default Gateway 

allows the configuration of the default gateway 

address to forward packets outside the subnet. 

Mode

Automatic

 (default) allows automatic selection of the default 

gateway. 

Static

 allows entering the default gateway IP address. 

Address

, available with 

Static

 mode, allows entering the IP 

address of the Default Gateway. The accepted range is from 

0000:0000:0000:0000:0000:0000:0000:0000 

to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF

. The default address 

is 

FE80:0000:0000:0000:0000:0000:0000:0000

. 

IPv6 Destination Address

 allows selecting the destination IP address 

for the stream that must start with 

FE80

. The accepted range is from 

0000:0000:0000:0000:0000:0000:0000:0001

 to 

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF.

 The default address is

 

2001::

. When the 

Address

 field is selected for editing using virtual 

keyboard, the 

Previous IPs

 button appears allowing the selection of a 

previously configured IP address. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands