manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 440

Test Results

428

88000 Series

Link OAM

Link OAM 

From the 

Test

 menu, tap

 Results

, and the 

Link OAM

 tab. 

Remote MAC Address

Indicates the remote OAM link partner MAC address. 

Remote OAM Information

OAM Version

 indicates the protocol version supported by the DTE.

Revision

 indicates the revision of the Information TLV. 

Multiplexer Action

 reports the Multiplexer Action: 

Forward

 indicates that the device is forwarding non-OAMPDUs to the 

lower sublayer. 

Discard

 indicates that the device is discarding non-OAMPDUs. 

Parser Action

 reports the Parser Action: 

Forward

 indicates that the device is forwarding non-OAMPDUs to the 

higher sublayer. 

Loopback

 indicates that the device is looping back non-OAMPDUs to 

the lower sublayer.

Discard

 indicates that the device is discarding non-OAMPDUs.

OAM Mode

 reports the OAM mode: 

Active

 indicates that the DTE is configured in 

Active

 mode.

Passive

 indicates that the DTE is configured in

Passive

 mode.

OUI

 reports the 24-bit IEEE Organizationally Unique Identifier field 

identifying the vendor. 

Maximum OAMPDU Size

 reports the maximum OAMPDU size in bytes, 

supported by the DTE. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands