EXFO Power Blazer 88000 Series User Manual Download Page 679

Page: 679 / 803

Power Blazer

667

14 Troubleshooting

Solving Common Problems

Before calling EXFO’s technical support, please read the following
common problems that can occur and their respective solution.

Problem

Possible Cause

Solution

Optical Laser LED is off and the
connector is not generating the
signal.

The

Laser On

option is disabled.

Ensure that the

Laser

button is

enabled (On).

There is a configuration mismatch
between the inserted transceiver
and the rate selected for the test
case.

Ensure that the transceiver is
supporting the rate used for the
test case.

The transceiver is not compatible
with the module

Ensure to use a compatible
transceiver. Refer to

Unable to edit the

Operator Name

Generate Report

page

This is the expected behavior when
the

EXFO Connect Server

check

box is selected in

EXFO Connect

Client

, since the

Operator Name

selected from the EXFO Connect
operator name list.

To edit the

Operator Name

- Clear the

EXFO Connect Server

check box from

EXFO Connect

Client
-

Close and restart the module

application.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands