manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 313

Test Setup - Test Configurator, Timer, and System

Power Blazer

301

Signal - Signal Configuration (DSn/PDH)

Force Release / Activate / Release

Force Release

 button, available with 

Auto-Response

 mode, 

allows releasing a loopback condition initiated from the network. 
Only available when a loopback is active. 

Activate

 button, available with 

Manual

 mode when no loopback is 

active, allows sending a loopback condition. 

Release

 button, available with 

Manual

 mode when a loopback is 

active, allows releasing the loopback condition. 

Loop-Up 

indicates the selected loop up code. 

Loop-Down 

indicates the selected loop down code. 

Modify Loop Codes

 button: See 

Modify Loop Codes button

 on 

page 299 for more information. 

Out-of-Band loop code

Loop-UP Code

Loop-Down Code

Line

00001110 11111111

00111000 11111111

Payload

00010100 11111111

00110010 11111111

Reserved For Network Use

00010010 11111111

00100100 11111111

ISDN Line (NT2)

00101110 11111111

00100100 11111111

CI/CSU Line(NT1)

00100000 11111111

00100100 11111111

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands