manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 83

Test Setup - Test Applications

Power Blazer

71

TCP Throughput

TCP Throughput 

The objective of this test is to find the TCP throughput based on the 
successfully transported bytes over the test time. Two units running a TCP 
Throughput test are required. One unit will act as the source (Local) and 
the other one as the destination (Remote). 

The local unit starts sending TCP segments using the Initial Window Size 
defined. The window size is adjusted following the TCP algorithm. The 
window size is incremented until the Maximum Window Size or 
congestion is reached. However, the window size will be reduced when 
congestion occurs, then incremented again as described above when the 
congestion is cleared. TCP Throughput and windows size statistics will be 
gathered throughout the test.

Typical TCP Throughput test application: 

Supported Interfaces/Rates: 10M to 1G.

Network

under test

Local Testing Unit

Remote Unit

EXFO Module

EXFO Module

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands