manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 602

Test Functions

590

88000 Series

OH - OTN

RES

, column 9-14, ODU OH: The six Reserved (RES) bytes are 

configurable from 

00

 (default for each byte) to 

FF

. 

PSI

, column 15, OPU/ODU OH: Tap the PSI field to configure (TX) or 

display (RX) the Payload Structure Identifier. 

TX: Select any TX byte from the list and its content is displayed 
below the list. Tap the 

Edit

 button to change its value. 

RX: Select any RX byte from the list and its content is displayed 
below the list. 

Link TX/RX Scrolling

, when selected (cleared by default), allows 

synchronizing both TX and RX table allowing to see the same TX 
and RX PSI byte numbers when scrolling from either TX or RX 
table. 

Foreground Signal Label

: Indicates the status of the MSI for each 

PSI#, either 

MSI TX

 (black), 

Expected MSI RX

 (green), or 

MSI 

Mismatch

 (red). 

OMFI

 or 

NJO

OMFI

, column 16, OPU OH: OPU Multi-Frame Identifier is only 

available for OPU4 of a mapped signal. This byte is not configurable. 

NJO

, column 16, ODU OH: The Negative Justification Opportunity byte 

is not configurable. Available either for non-concatenated signal or on 
the LO of a concatenated signal. 

RX 

RX OH Byte Details

 displays the content of the selected OH RX byte. 

Tap on any OH RX byte to see its content 

Legend TX/RX

 indicates the path level for all OH bytes. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands