manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 609

Test Functions

Power Blazer

597

OH - SONET/SDH

For 

M0 and M1

 computation method:

Z2

: Growth. Available with OC-3, OC-12, and OC-48 signal, this byte is 

located in STS-1 #1 up to STS-1 #48 except for timeslots used by M0 
and M1. 

Undefined “--”

 for all other timeslots not covered by M0, M1, and Z2.

M0 

or 

M1 (SDH) 

M0

: MS-REI. STM-1 channel #1 of a STM-0 signal; channel #2 of an 

STM-64 signal. 

M1

:MS-REI. STM-1 channel #1 of a STM-1 signal; channel #3 of an 

STM-N signal (N>1). 

Undefined “--”

 for all other channels not covered by M0, and M1. 

E2

: Orderwire. Provides a 64 Kbit/s voice channel for communication 

between LTEs. This byte is only defined for the first STS-1/STM-1 frame 
of a composite signal. 

M0

Located in STS-1 #4

M1

Located in STS-1 #7

Indicates

0000 0000

0000 0000

0 BIP violation

0000 0000

0000 0001

1 BIP violation

:

:

:

0000 0110

0000 0000

1536 BIP violations

0000 0110 to 

1111 1111

0000 0001 to 

1111 1111

0 BIP violation

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands