manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 281

Test Setup - Test Configurator, Timer, and System

Power Blazer

269

S-OAM and MPLS-TP OAM

Pass/Fail Verdict 

Pass/Fail Verdict

 check box when selected (default) enables the use of the 

pass/fail verdict. A global fail verdict is declared when any of the following 
condition is met: 

Link Down

 alarm, 

Loss Continuity

 alarm, or any fail 

verdict for 

Frame Delay

, 

Frame Loss

, 

Synthetic Loss

 (Only applicable to 

Ethernet OAM), 

Frame Delay Failure

, 

Frame Loss Failure

, 

Synthetic Loss 

Failure

 (Only applicable to Ethernet OAM), 

Loopback Failure

, or 

Test 

Failure

. 

Thresholds 

Available with G.8113.1, Y.1731 and MEF OAM Modes when Pass/Fail verdict 
is enabled. The verdict is PASS when the measured value is lower or equal 
to the threshold value. 

Frame Delay Threshold (ms)

 allows setting the threshold value of 

frame delay: 

0.001

 to 

8000

 ms (default is 

50

ms). 

Frame Loss Threshold (%)

 allows setting the threshold value of frame 

loss: 

0.001

 to 

100

% (default is 

10

%). 

Synthetic Loss Threshold (%

), available with Ethernet OAM (Y.1731 

and MEF), allows setting the threshold value of Synthetic Loss: 

0.001

 to 

100

% (default is 

10

%). 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands