EXFO Power Blazer 88000 Series User Manual Download Page 600

Page: 600 / 803

Test Functions

588

88000 Series

OH - OTN



JC2

, column 16, OPU OH: Controlled by GMP function. This byte is not

configurable.

, column 16, OPU OH:



Bits 1-6, Reserved (RES), are configurable from binary

000000

(default) to

111111



Bits 7-8, Justification Control (JC), are configurable from binary

(default) to

. Not available with ODU mux. Changing the JC

value will corrupt the payload.

Row 3



TCM3/TCM2/TCM1

, columns 1-9, ODU OH: See

TCM6/TCM5/TCM4

page 587 for more information.



, column 10-12, ODU OH: The Path Monitoring overhead contains

the following bytes.

The first PM byte (column 10) contains the TTI byte that is not
configurable.

The second PM byte (column 11) contains the BIP-8 byte and is
automatically generated for each frame. This byte is not configurable.

The third PM byte (column 12) contains the following sub-fields. This
byte is configurable from

. The default value is



EXP

., column 13-14, ODU OH: The two Experimental overhead bytes

are configurable form

(default for each byte) to

1. Depending on the test MUX/Mapping.

Bit 1-4

Bit 5

Bit 6-8

BEI

BDI

STAT

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88000 Series, User Manual

Search results

Summary of Contents for Power Blazer 88000 Series

Reviews:

Brands by name

Popular brands