manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 528

Test Results

516

88000 Series

Summary (TCP Throughput)

Summary (TCP Throughput) 

From the

 Test

 menu, tap 

Results

, and the 

Summary

 tab. 

Test Status

 indicates the actual test status as follows: 

Start Time

 indicates the date and time the test was started. The date 

and time is reset every time the test is restarted or reset. 

Test Recovery

, when displayed, indicates that the test has 

automatically recovered from a power failure. The number of 
occurrences is also displayed next to the 

Test Recovery

 field. Refer to 

Power Failure Recovery

 on page 659. 

Logger Full

, when displayed, indicates that the logger is full. Refer to 

Logger

 on page 432. 

Test Status

Description

“--” 

The test is not running or results are not available.

In Progress

The test is running.

Completed

The test is completed, stopped at the planned time, or 
manually stopped when there is no set timer.

Aborted

 - 

<Reason>

The test is interrupted; stopped before the set timer. Possible 

<Reason> are: 

TCP Session Closed

 or 

Remote IP Not Found

.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands