manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 711

Glossary

Power Blazer

699

1588 PTP

The 1588 PTP supports the following Master/Client communication; 
however 

Unicast

 is used for the Telocom Profile.

Multicast

: A Master clock sends its Sync/Follow Up and Delay 

Response in a multicast mode. A Client can collect information from 
many Master clocks and select the Master clock that is best suited for 
its application.

Unicast

: A dedicated communication link is established between the 

Master and the Client clock. This mode of operation requires a 
negotiation which is initiated by the Client clock. 

The 1588 PTP messages can be mapped on the following protocols; 
however UDP IPv4 is used for the Telecom Profile.

UDP/IPv4

UDP/IPv6 

Ethernet 

1588 PTP Profiles

The purpose of a PTP profile is to allow organizations to specify particular 
selections of attribute values and optional features of PTP that, when using 
the same transport protocol, inter-work and achieve a performance that 
meets the requirements of a given application.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands