manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 237

Test Setup - Test Configurator, Timer, and System

Power Blazer

225

Network

VLAN

VLAN Tag

 check box, when selected (cleared by default), enables and 

allows setting up to 3 stacked VLANs. 

For each VLAN tag enabled, C-VLAN / S-VLAN / E-VLAN, the following 
parameters are configurable.

VLAN ID

 choices are 

0

 through 

4095

; refer to 

VLAN ID and Priority

 on 

page 758 for more information. 

Priority

, VLAN user priority, choices are 

0

 (default) to 

7

. Refer to 

VLAN 

ID and Priority

 on page 758 for more information. 

Type

, VLAN Ethernet Type, choices are 

0x8100

 (default for C-VLAN), 

0x88A8

 (default for S-VLAN), 

0x9100

 (default for E-VLAN), 

0x9200

, 

and 

0x9300

. 

Drop Eligible

, when set to 

Yes

 (DEI = 1), the transmitted frames will 

be dropped first on receipt when congestion occurs under test. Drop 
Eligible is not available when VLAN type is 8100. This setting is set to 

No

 by default. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands