manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 154

Test Setup - Test Configurator, Timer, and System

142

88000 Series

BERT and Unframed BERT

Bit Error 

Pass/Fail Verdict

 allows enabling bit-error-rate pass/fail verdict by 

selecting either 

Bit Error Count

 or 

Bit Error Rate

. The default value is 

Disabled

. 

BER Threshold

 allows entering the threshold 

Count

 or 

Rate 

value that 

will be used to declare the pass/fail verdict. The 

BER Threshold

 

applies to individual pattern for 

Multi-Pattern

. 

For 

Count

, enter the maximum bit error count allowed before 

declaring a fail verdict: 

0

 (default) to 

999999

. 

For 

Rate

, enter the maximum bit error rate allowed before declaring a 

fail verdict: 

1.0E-14

 to 

1.9E-01

. The default value is 

1.0E-12

. 

Service Disruption 

The Service Disruption Time (SDT) corresponds to the duration associated 
to a defect that occurred in the network. For example a disruption that 
occurs during a network switching from the active channels to the backup 
channels or vice versa. 

Note:

The service disruption measurements are cleared when changing the 
criteria. Service Disruption is not available for 

Multi-Pattern

.

Defect

 allows choosing on which layer and defect the service 

disruption time test will be performed. Choices depend on the 
selected test path. 

Layer

Defect

Interface

OTN/SONET/SDH: LOS

a

DSn: LOS, BPV, EXZ
PDH: LOS, CV 

Section/RS LOF-S/RS-LOF

, 

B1

Line/MS AIS-L/MS-AIS

, 

RDI-L/MS-RDI

, 

REI-L/MS-REI

, 

B2

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands