manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 275

Test Setup - Test Configurator, Timer, and System

Power Blazer

263

RFC 2544 - Subtests

Frame Loss Threshold (%)

 sets the threshold

1

 value of frame loss. 

The range is from 

0.000 

to 

100.000

 (default is 

0.100

) and it applies to 

all frame sizes when applicable. 

Latency Threshold 

/ 

Round-Trip Latency Threshold

 sets the 

threshold value as the maximum delay in 

ms

 or 

μ

s

. The range is from 

0.5

 to 

8000.0 ms 

(default is 

125.0

ms) and it applies to all frame sizes 

when applicable. For 

Dual Test Set

, only available with 

Round-Trip 

Latency Measurement Mode

 (see 

Latency Configuration

 on 

page 260). 

One-Way Latency Threshold

, available for 

Dual Test Set

 with 

One-Way Latency Measurement Mode

 (see 

Latency Configuration

 on 

page 260), sets the maximum one-way latency value in millisecond, 
allowed for all frame sizes: 

0.005

 to 

500 ms

 (default is 

125 ms

). 

Latency Unit

 allows selecting either 

ms

 or 

μ

s

 as the reference unit for 

the 

Latency Threshold

. 

1. The verdict is PASS when the received/measured value is lower or equal to the threshold value. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands