manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 206

Test Setup - Test Configurator, Timer, and System

194

88000 Series

Interface (Ethernet, Packet Sync, Fibre Channel, and Wireless)

TX Frequency 

Note:

The following TX Frequency information applies to serial interface only, 
refer to 

TX Frequency

 on page 175 for parallel interfaces. Not available 

when using an active copper SFP.

TX Frequency (GHz)

 indicates the frequency (actual fre 

Frequency offset) used for transmission. 

Note:

Frequency offset is not available with OBSAI, CPRI in RRH emulation mode, 
RFC 6349 test application. 

Offset (ppm)

 check box, when selected (cleared by default), allows 

setting the frequency offset that will be generated: ±120 ppm for all 
Ethernet rates at the exception of 10GE WAN which is ±50 ppm; not 
supported for 10M electrical. Use the “+” or “-” button to respectively 
increment or decrement the frequency offset value based on the 
defined 

Increment/Decrement Size

, or directly type the frequency 

offset value in the field. 

Step Size (ppm)

 allows setting the increment/decrement value (from 

0.1 to the maximum offset) that will be used when changing the 
frequency offset with the “+” or “-” button. 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands