manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 141

Test Setup - Test Configurator, Timer, and System

Power Blazer

129

Modify Structure Button

For Wireless Test Application 

Port 1

 and 

Port 2

 are only displayed when 

Dual Port

 topology is 

selected and allows configuring each port individually. 

Interface/Rate

 allows the selection of the interface rate. 

Connector

 is the module’s port available for the selected interface/rate 

(see table above). 

Framing

 

Framed L2

 (default) is mainly used to validate connectivity with 

the base station (REC) or remote radio head (RE) over the fiber 
interface. 

Unframed

 is mainly used to validate the continuity of the dark fiber 

at CPRI or OBSAI (3.1 Gbit/s) rate. 

Interface Rate

Connector

a

a.

Availability of connectors depend on the model. 

8870/8880 

88200NGE 

CPRI - 1.2G
CPRI - 2.4G 
CPRI - 3.1G 
CPRI - 4.9G 
CPRI - 6.1G 
CPRI - 9.8G 

Port 1 - SFP+ 
Port 2 - SFP+

Port 1 - SFP+

OBSAI - 1.5G 
OBSAI - 3.1G 
OBSAI - 6.1G 

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands