manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 599

Test Functions

Power Blazer

587

OH - OTN

Row 2

RES

, columns 1-2, ODU OH: The two Reserved (RES) bytes are 

configurable from 

00

 (default for each byte) to 

FF

. 

PM & TCM

, column 3, ODU OH: The Path Monitoring and Tandem 

Connection Monitoring byte is configurable from 

00

 (default) to 

FF

. 

TCM ACT

, column 4, ODU OH: The Tandem Connection Monitoring 

Activation is configurable from 

00

 (default) to 

FF

. 

TCM6

/

TCM5

/

TCM4

, column 5-13, ODU OH: The Tandem Connection 

Monitoring overhead contains the following bytes. 

The first TCMi byte contains the TTI multiframe byte and is only 
configurable from 

Traces (OTN)

 on page 332.

The second TCMi byte contains the BIP-8 byte and is automatically 
generated for each frame. This byte is not configurable.

The third TCMi byte contains the following sub-fields. This byte is 
configurable from 

00

 to 

FF

. The default value is 

00

 when TCMi is 

disabled, and 01 when enabled.

FTFL

, column 14, ODU OH: The Fault Type Fault Location multiframe 

byte is only configurable from 

FTFL/PT and PT

 on page 177. 

JC5

 or 

RES

1

 

JC5

, column 15, OPU OH: Bits 1-3 set to all-0s, and bits 4-8 are 

controlled by GMP function. This byte is not configurable. 

RES

, column 15, OPU OH: The Reserved (RES) byte is configurable 

from 

00

 (default) to 

FF

. 

Bit 1-4

Bit 5

Bit 6-8

BEI/BIAE

BDI

STAT

1. Depending on the test MUX/Mapping.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands