manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 233

Test Setup - Test Configurator, Timer, and System

Power Blazer

221

Network

IP

IP Version

 allows the selection of either 

IPv4

 (default) or 

IPv6

. Only IPv4 is 

supported for TCP Throughput and RFC 6349 test applications. 

For 

IPv4

 the following configuration parameters are available. 

Automatic IP (DHCP)

 check box, when selected (cleared by default), 

allows obtaining an IP address dynamically from a DHCP (Dynamic 
Host Configuration Protocol) server. 

IP Address

1

: Enter the IP address of the port. The default setting is 

10.10.x.y, where x and y are respectively the two least significant bytes 
of the port default MAC address. 

Subnet Mask

1

: Enter the Subnet Mask. The default setting is 

255.255.000.000

. 

Default Gateway

1

 check box, when selected (cleared by default), 

allows entering a default Gateway IP address. When the 

Default 

Gateway

 check box is selected, its default address is 

0.0.0.0

. 

1. Not configurable when the 

Automatic IP (DHCP) 

check box is selected.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands