manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 465

Test Results

Power Blazer

453

S-OAM and MPLS-TP OAM

Invalid Payload

 indicates the count of received LBR frames having 

either a TLV type different than the one transmitted, Bit error or wrong 
data value detected in the data payload of a Data TLV, Bit error, Pattern 
Loss, or Pattern Type mismatch of a Test TLV. 

Successful

 indicates the count of received LBR frames having no 

errors. 

Failed

 indicates the count of LBR frames declared as invalid. 

Test 

Status

 displays the status of the test function (refer to page 511). 

TX TST

 indicates the count of transmitted TST frames. 

RX TST

 indicates the count of valid TST frames received. A valid frame 

for S-OAM has its source MAC address matching the Peer MEP MAC 
address; destination MAC address matching either the unit port Unicast 
MAC address or a Multicast class 1 address

1

; and VLANs matching the 

unit port VLANs. A valid frame for MPLS-TP OAM has its destination 
MAC address matching either the unit MAC address, FF:FF:FF:FF:FF:FF, 
or 01:00:5E:90:00:00; VLANs matching the unit port VLANs; and MPLS 
Labels matching the local MPLS Label Stack configuration.

Invalid TST

 indicates the count of TST frames received from the peer 

MEP with incorrect MEG/MD level. 

Invalid Payload

 indicates the count of received TST frames having 

either an unsupported pattern type, or bit error / pattern loss detected 
in the payload. 

Successful

 indicates the count of received TST frames having no 

errors. 

Failed

 indicates the count of TST frames declared as invalid. 

1. Refer to 

Unicast/Multicast Addresses for Ethernet OAM

 on page 757 for more information.

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands