manualshive.com logo in svg

EXFO Power Blazer 88000 Series, User Manual

Share
Download
EXFO Power Blazer 88000 Series User Manual Download Page 386

Test Results

374

88000 Series

Alarms/Errors Overview

Interface 

Alarms

 

LOS

 (Loss Of Signal)

 

RX

: Absence of an input signal or an all-zeros pattern is received. 

Available for each Optical Lane for parallel interfaces.

For CPRI Framed L2: Absence of an input signal or at least 16 
8B/10B code violations occur in one hyperframe. 

For Wander 1PPS interface: Either no pulse is received or no pulse 
is received within 1 second ±100 ms after the previous pulse. 

LOC Lane 

(Loss Of Clock Lane) is available for each Physical Lane for 

parallel interfaces. 

RX

: The module is unable to lock on the 

Physical/CAUI/CAUI-4/XLAUI/400GAUI-16 link interface. 

Frequency

 (available for each Physical Lane for parallel interfaces). 

Not available when using an active copper SFP. 

RX

: The received signal frequency meets the standard specifications 

(green) or not (red). 

For Ethernet 

10/100/1000M Electrical

, 

100M Optical

, 

1GE Optical

, 

10GE LAN/WAN

, 

25GE

, or Fibre Channel 

1X

/

2X

/

4X

/

8X

/

10X/16X

 

interface/rate, the frequency range is ± 100 ppm. 

For parallel interfaces: 

Rate

Optic Type

Frequency

40GE

4x10G

10.3125 Gbit/s ± 100 ppm

OTU3

4x10G

10.7546 Gbit/s ± 20 ppm

OTU3e1

4x10G

11.1427 Gbit/s ± 20 ppm

OTU3e2

4x10G

11.1458 Gbit/s ± 20 ppm

100GE

4x25G

10.3125 Gbit/s ± 100 ppm

400GE 

8x50G

26.5625 Gbit/s ± 100 ppm

OTU4

4x25G

11.181 Gbit/s ± 20 ppm

Summary of Contents for Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands